Roymech engineering encyclopedia

Eyebolts with Link to BS 4278:1984 – Dimensions and Safe Working Loads


Legacy standard: BS 4278:1984 is withdrawn. This page preserves the original dimensional and safe working load data for reference when identifying, maintaining or assessing older lifting equipment.

This page provides dimensions and safe working loads for metric eyebolts with link to BS 4278:1984 Table 2. The data are retained as an engineering reference for existing equipment and legacy designs manufactured or specified to this standard.

Need help selecting lifting equipment? See the Lifting Equipment Help and Selection Guide for guidance on eyebolts, Dee and bow shackles, WLL, loading direction, sling angles and choosing between current and legacy RoyMech references.

The link allows the lifting load to be transmitted to the eyebolt without requiring an intermediate shackle and enables the assembly to accommodate inclined loading in any plane, subject to the loading limitations specified in BS 4278.

Eyebolt with Link to BS 4278:1984 Table 2

Eyebolt with link dimensions to BS 4278:1984 Table 2

The following table preserves the RoyMech reference data for metric eyebolts with link to BS 4278:1984 Table 2. Dimensions B to M and the link dimensions correspond to the dimensional diagram above.

The safe working load shown in Table 2 is the marked SWL for a single eyebolt under axial loading. BS 4278 also specifies conditions for inclined loading, as described below.

Safe Working Load
(tonnes)
Metric Thread Eyebolt Dimensions (mm) Link Dimensions (mm)
B C D E F G H J K L M d Bd Ld
1.0 M20 39 24 9 15 12 20 27 1 4 14 12 13 24 53
1.6 M24 47 29 11 18 14 23 32 1 5 16 14 15 29 63
2.5 M30 60 37 14 23 18 30 41 2 6 21 18 19 37 80
4.0 M36 75 46 17 29 23 38 52 2 7 26 23 24 46 102
6.3 M48 94 58 22 36 29 47 65 3 9 32 29 30 58 126

Note: In BS 4278, dimension K is a minimum dimension and may be increased to facilitate manufacture.

Inclined Loading of BS 4278 Eyebolts with Link

Unlike the dynamo eyebolt specified in the same standard, the eyebolt with link is specifically intended to accommodate non-axial loading. BS 4278 describes it as suitable for inclined loading in any plane.

The eyebolt may be loaded in any direction up to its marked safe working load provided that the angle between the applied load and the axis of the eyebolt screw thread does not exceed 15°.

For non-axial loading at angles greater than 15°, the safe working load must be reduced in accordance with the loading arrangements and reduction factors specified by BS 4278.

When eyebolts with link are used in pairs for inclined lifting, BS 4278 Table 8 gives maximum recommended working loads according to the angle between the sling legs.

Important identification point: BS 4278 specifically distinguishes an eyebolt with link manufactured to Table 2 from a collar eyebolt to Table 1 to which a link has subsequently been fitted. The two arrangements should not be assumed to be equivalent.

Use of Eyebolts with Link

The eyebolt with link was intended as the general-purpose eyebolt arrangement within BS 4278, particularly where loading could not be confined to the plane of the eye.

The attached link provides a suitable connection for a sling hook without requiring an intermediate shackle and allows the lifting force to be transmitted through the assembly over a wider range of load directions than a conventional collar eyebolt.

This makes the BS 4278 eyebolt with link particularly relevant to legacy lifting arrangements involving pairs of lifting points and inclined sling legs.

Selection and Inspection

When identifying or assessing a legacy eyebolt with link, the dimensional data should be considered together with the markings and condition of the complete assembly.

Checks should include the thread size and condition, adequate thread engagement, the strength and condition of the supporting component, deformation or wear of the eye and link, corrosion, cracking, damaged welds or other deterioration, and confirmation that the assembly corresponds to the intended BS 4278 configuration.

Safety-critical application: The values on this page reproduce legacy BS 4278 data and are retained for engineering reference. For an actual lifting operation, the identity, condition, installation and suitability of the lifting point should be established by a competent person.

Legacy Standard Reference

The information on this page deliberately remains associated with BS 4278:1984. It is retained for engineers identifying, maintaining or assessing machinery and lifting equipment originally designed to this withdrawn standard.

Current-standard lifting points and their associated requirements will be covered separately on RoyMech rather than replacing or mixing the historical BS 4278 data presented here.

Related Lifting Equipment