Roymech engineering encyclopedia

ISO 3601 O-Rings – Dimensions, Sizes and Housing Design


The ISO 3601 series provides the principal international standards for O-ring dimensions, tolerances, housing dimensions, quality requirements, back-up rings and elastomeric material specifications.

This RoyMech reference is intended primarily for engineers selecting O-rings for new equipment to current standards. Separate dimensional tables provide the complete O-ring size data, while this page explains the different dimensional systems and the main design considerations.

Need help selecting a seal for a rotating shaft? See the Seal Selection Guide for guidance on rotary shaft seals, O-rings, mechanical seals, packing and gaskets, and on selecting a seal for the operating speed, pressure, temperature, fluid and contamination conditions.

O-Ring Dimensions & Housing Data

For direct access to the engineering data, select the appropriate dimensional or housing reference below.

Working with older equipment? RoyMech retains its legacy O-ring dimensions and housing data for equipment designed using standards including BS 1806 and BS 4518.

Current ISO 3601 Standards

Standard Subject Engineering Use
ISO 3601-1:2012
Amd 1:2019
Inside diameters, cross-sections, tolerances and designation codes O-ring size selection and dimensional specification
ISO 3601-2:2025 Housing dimensions for general applications Groove and housing design for Class A and specified Class B O-rings
ISO 3601-3:2005
Amd 1:2018
Quality acceptance criteria Surface quality and acceptance requirements
ISO 3601-4:2008 Anti-extrusion rings Back-up ring dimensions and tolerances
ISO 3601-5:2015 Elastomeric materials Material specifications for industrial O-rings

ISO 3601-1:2012 remains the current published Part 1 and was confirmed in 2022. It also has a published 2012 corrigendum and Amendment 1:2019.

ISO 3601-2:2025 is the current third edition of Part 2 and supersedes ISO 3601-2:2016.

Basic O-Ring Dimensions

An O-ring is principally identified by two dimensions:

d1 – Inside Diameter

The nominal internal diameter of the unstretched O-ring.

d2 – Cross-Section Diameter

The nominal diameter of the circular O-ring cross-section.

ISO 3601-1 specifies the values of d1 and d2, their dimensional tolerances and the associated size/designation codes.

Understanding the O-Ring Size Systems

One source of confusion when selecting O-rings is that several dimensional systems are encountered in engineering practice. Dimensions quoted in millimetres are not necessarily part of the same dimensional series.

For example, traditional O-ring sizes originating from inch-based systems are commonly expressed as metric dimensions in catalogues. A quoted cross-section of 3.53 mm is therefore not the same thing as deliberately selecting a nominal metric cross-section simply because both dimensions are expressed in millimetres.

Class A O-Rings

ISO 3601-2 identifies Class A O-rings for general industrial applications. These O-rings conform to ISO 3601-1.

Many engineers will recognise dimensions within this group from traditional industrial O-ring size systems.

Class B O-Rings and Metric Hardware

ISO 3601-2 also provides housing requirements for Class B O-rings used with selected metric-dimensioned hardware, including fluid-power cylinder bores and piston rods.

This is particularly relevant to machinery designed directly around metric bore and rod dimensions rather than around a traditional inch-derived O-ring size.

Aerospace O-Rings

ISO 3601-1 also includes O-rings intended for aerospace applications. These should not be confused with the general industrial series merely because some nominal cross-sections are very similar.

Housing dimensions for aerospace O-rings specified in ISO 3601-1 are addressed separately in Annex A of ISO 3601-2:2025.

Typical Cross-Sections Encountered

The following examples illustrate why the dimensional family must be identified rather than selecting an O-ring merely from an approximate measured cross-section.

Example dimensional family Typical nominal cross-sections encountered Important point
Traditional general-industrial / inch-derived sizes 1.78, 2.62, 3.53, 5.33, 6.99 mm Dimensions are normally shown in millimetres but have their origins in traditional inch-based size series.
Metric equipment Metric O-ring dimensions are selected in conjunction with the applicable metric hardware and dimensional series. Do not substitute the nearest inch-derived section simply because its metric value is close.
ISO aerospace examples 1.80, 2.65, 3.55, 5.30, 7.00 mm Similar-looking cross-sections do not establish interchangeability with another O-ring series.
Important: Similar nominal cross-sections do not by themselves establish interchangeability. Check the applicable size code, inside diameter, cross-section, tolerances, application class and housing dimensions.

Identifying an Existing O-Ring

When the original part number or standard is unknown, measure both the inside diameter and cross-section of the O-ring.

The basic comparison dimensions are:

  • d1 – inside diameter
  • d2 – cross-section diameter

An old or used O-ring should not be expected to reproduce its original nominal dimensions exactly. Ageing, compression set, swelling, shrinkage, wear and permanent stretch can all affect measurements.

Compare measured dimensions with the appropriate dimensional table, allowing for changes caused by service and ageing. Where measurements fall between nominal sizes, also check the original housing dimensions and applicable size series before selecting a replacement.

BS 1806 and ISO 3601

BS 1806 dimensions remain familiar to engineers because the standard was extensively used for industrial O-rings and a large amount of existing machinery was designed around those sizes.

The James Walker O-ring guide notes that BS 1806 was superseded by BS ISO 3601-1 for O-ring dimensions and BS ISO 3601-2 for housing dimensions. It also notes that BS 1806 continues to be widely referenced in industry.

Many non-aerospace size codes and nominal dimensions are therefore familiar between the older and newer systems, but this should not be interpreted as meaning that every dimensional requirement and tolerance is identical.

RoyMech policy: Current ISO 3601 information is provided for new designs while useful BS 1806 and BS 4518 information is retained separately for maintenance, replacement and existing equipment.

ISO 3601-2:2025 O-Ring Housings

ISO 3601-2:2025 specifies housing dimensions for Class A O-rings used in general industrial applications and for Class B O-rings used with selected metric-dimensioned hardware such as fluid-power cylinder bores and piston rods.

The standard covers general hydraulic and pneumatic applications both with and without anti-extrusion or back-up rings.

Two Design Approaches

The current standard recognises two common approaches to O-ring housing design.

O-Ring First

Select the appropriate O-ring and then determine suitable hardware dimensions around the selected seal.

Hardware First

Where the bore or rod dimensions are already fixed, select the most appropriate O-ring and housing arrangement for that hardware.

Housing Information

The principal housing information required by an engineer includes:

  • Groove diameter
  • Groove depth
  • Groove width
  • Bore or rod diameter
  • Diametral clearance
  • Edge and groove radii
  • Lead-in chamfers
  • Surface finish
  • Back-up ring provision where required
Current housing reference: RoyMech's older BS housing tables should not be assumed to represent ISO 3601-2:2025 requirements. For new designs see ISO 3601-2:2025 O-Ring Housing & Groove Dimensions .

O-Ring Design Considerations

Squeeze

An O-ring seals by being deformed within its housing. The difference between the free O-ring cross-section and the available installed space produces the initial sealing contact.

For a simplified arrangement, nominal percentage squeeze can be expressed as:

S = d 2 - h d 2 × 100

where:

  • S = nominal squeeze, %
  • d2 = O-ring cross-section diameter
  • h = effective installed housing depth in the direction of compression

The equation is useful for understanding the relationship between cross-section and housing depth, but a standards-compliant housing should use the appropriate ISO 3601-2 dimensions and tolerances.

Stretch and Circumferential Compression

Fitting an O-ring over a shaft or piston can stretch its inside diameter. Stretch also reduces the effective cross-section slightly and therefore affects installed squeeze.

Conversely, excessive circumferential compression can cause an O-ring to buckle or seat incorrectly in its groove.

Groove Fill

Elastomers behave substantially as incompressible materials. When an O-ring is squeezed, the material is displaced within the available housing volume rather than simply reducing in volume.

Adequate housing volume is therefore required to accommodate:

  • O-ring dimensional tolerances
  • Hardware manufacturing tolerances
  • Thermal expansion
  • Fluid-induced swelling
  • Dynamic movement where applicable

Extrusion Clearance

Pressure can force an elastomeric O-ring into the clearance between mating components. This is known as extrusion.

Extrusion tendency depends on several interacting factors, including:

  • Pressure
  • Clearance gap
  • Elastomer hardness and mechanical properties
  • Temperature
  • Pressure cycling
  • Fluid compatibility and swelling

Back-Up Rings – ISO 3601-4

Anti-extrusion or back-up rings are used to support an O-ring where the combination of pressure and hardware clearance could otherwise force the elastomer into the extrusion gap.

ISO 3601-4 specifies dimensions and tolerances for specified types of back-up ring intended for use with O-rings and corresponding housings.

Where pressure can act alternately from both directions, back-up support may be required on both sides of the O-ring.

Static and Dynamic Applications

Application Typical Arrangement Important Design Factors
Static axial O-ring compressed between stationary faces Pressure direction, squeeze, groove volume and flange geometry
Static radial Stationary concentric cylindrical components Radial squeeze, clearance and assembly
Reciprocating Linear movement between sealing surfaces Friction, wear, lubrication, extrusion clearance and surface finish
Rotary / oscillating Rotational or oscillating relative movement Speed, frictional heating, lubrication, material and specialised housing requirements

O-Ring Material Selection

Correct dimensions do not by themselves make an O-ring suitable for an application. The elastomer must also be compatible with the fluid, temperature, pressure and operating environment.

Elastomer Abbreviation General Characteristics
Nitrile rubber NBR Widely used with mineral oils and in hydraulic applications. Performance depends on compound.
Hydrogenated nitrile HNBR Improved temperature, ageing and mechanical performance compared with conventional NBR in suitable applications.
Ethylene-propylene EPM / EPDM Good resistance to water, steam and weathering. Generally unsuitable for mineral oils.
Fluoroelastomer FKM Used for elevated-temperature service and resistance to many oils, fuels and chemicals.
Silicone VMQ Wide useful temperature range but relatively limited tear and abrasion resistance.
Fluorosilicone FVMQ Useful low-temperature characteristics combined with resistance to many hydrocarbon fuels and oils.
Perfluoroelastomer FFKM Very high chemical and temperature resistance for severe service, depending on compound.

Individual compounds within an elastomer family can have substantially different chemical, temperature, compression-set and mechanical properties. Material family alone is therefore insufficient for critical applications.

Rapid Gas Decompression

High-pressure gas applications require consideration of rapid gas decompression (RGD).

Gas absorbed by an elastomer at high pressure can expand internally if system pressure is reduced faster than the gas can diffuse from the material. This can produce blistering, cracking or internal damage.

RGD resistance should therefore be considered when selecting seals for high-pressure gas service.

Surface Finish and Installation

Housing and mating-surface condition can be as important as the O-ring itself, particularly in dynamic service.

Check:

  • Surface finish
  • Machining direction where relevant
  • Absence of burrs and sharp edges
  • Lead-in chamfers
  • Extrusion clearances
  • Surface damage or corrosion
  • Lubrication requirements

Threads, splines, keyways and sharp ports should not be allowed to cut or abrade the O-ring during assembly. Suitable installation sleeves or other protection should be used where necessary.

O-Ring Selection for a New Design

  1. Establish whether the seal is static or dynamic.
  2. Identify the fluid or gas being sealed.
  3. Establish the complete operating-temperature range.
  4. Determine normal and maximum pressure.
  5. Select an appropriate elastomer and compound.
  6. Establish whether the design uses a general-industrial, metric-hardware or other applicable O-ring dimensional series.
  7. Select the O-ring dimensions and tolerances from ISO 3601-1.
  8. Determine the corresponding housing requirements from the current ISO 3601-2.
  9. Check extrusion clearance and whether back-up rings are required.
  10. Check squeeze, stretch/compression and groove fill across the complete tolerance range.
  11. Specify appropriate quality and material requirements.
  12. Check surface finish, assembly and lubrication requirements.

O-Ring Selection for Existing Equipment

When replacing an O-ring in existing machinery, do not assume that the equipment was designed to the current ISO dimensional system.

  1. Identify the original standard or part number where possible.
  2. Measure the existing housing.
  3. Measure the O-ring inside diameter and cross-section.
  4. Allow for dimensional changes caused by service and ageing.
  5. Compare the measurements with the appropriate dimensional series.
  6. Verify material compatibility with the operating fluid and temperature.
  7. Check the existing housing before substituting an O-ring from a different dimensional system.

For older machinery see: O-Rings – Legacy BS 1806 / BS 4518 Dimensions and Design Data .

Related RoyMech References

Standards and Technical References

Engineering use: RoyMech provides engineering reference information and guidance. Where contractual, regulatory, safety-critical or formally standards-compliant design is required, the applicable current standard and manufacturer's application data should also be consulted.
�